atmel_mci atmel_mci.0: Atmel MCI controller at 0xfff80000 irq 11, 1 slots

Kernel command line: console=ttyS0,115200 rw rootwait root=/dev/mmcblk0p2

Start SD card AT91Bootstrap...
Image size: 0x3c75c4, load_addr: 0x70008000, ep: 0x70008000
relocating linux kernel to proper address, dst: 0x70008000, src: 0x72000040, len: 0x3c75c4, machid: 0x8a4

Start SD card AT91Bootstrap...
Image size: 0x439220, load_addr: 0x70008000, ep: 0x70008000
relocating linux kernel to proper address, dst: 0x70008000, src: 0x72000040, len: 0x439220, machid: 0x8a4
Linux version 2.6.36-rc6 (spirit@localhost) (gcc version 4.5.2 (Sourcery G++ Lite 2011.03-41) ) #601 Sat Jan 14 10:35:23 MSK 2012
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: SK-MAT91SAM9G45
Ignoring unrecognised tag 0x54410009
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 400 MHz, master 133 MHz, main 12.000 MHz
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext2
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60496k/60496k available, 5040k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffa00000 - 0xffe00000 ( 4 MB)
vmalloc : 0xc4800000 - 0xfee00000 ( 934 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0028000 ( 128 kB)
.text : 0xc0028000 - 0xc0404000 (3952 kB)
.data : 0xc041c000 - 0xc04411a0 ( 149 kB)
Hierarchical RCU implementation.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:192
AT91: 160 gpio irqs in 5 banks
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
regulator: dummy:
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.0: using pins 52 (SDA) and 53 (SCL)
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource pit
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
msgmni has been set to 118
io scheduler noop registered (default)
atmel_lcdfb atmel_lcdfb.0: backlight control is not available
atmel_lcdfb atmel_lcdfb.0: 750KiB frame buffer at 73900000 (mapped at ffa00000)
Console: switching to colour frame buffer device 100x30
atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00500000 (mapped at c4814000), irq 23
atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL
atmel_usart.2: ttyS2 at MMIO 0xfff90000 (irq = 8) is a ATMEL_SERIAL
brd: module loaded
loop: module loaded
No NAND device found.
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14)
atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffa8000 (irq 15)
macb macb: invalid hw address, using random
MACB_mii_bus: probed
eth0: Atmel MACB at 0xfffbc000 irq 25 (5e:c2:24:b4:05:9b)
eth0: attached PHY driver [Micrel KS8001 or KS8721] (mii_bus:phy_addr=ffffffff:01, irq=-1)
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt73usb
usbcore: registered new interface driver rt2800usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
atmel-ehci atmel-ehci: Atmel EHCI UHP HS
atmel-ehci atmel-ehci: new USB bus registered, assigned bus number 1
atmel-ehci atmel-ehci: irq 22, io mem 0x00800000
atmel-ehci atmel-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 2
at91_ohci at91_ohci: irq 22, io mem 0x00700000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
USB Serial support registered for moto-modem
usbcore: registered new interface driver moto-modem
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
atmel_usba_udc atmel_usba_udc: MMIO registers at 0xfff78000 mapped at c481e000
atmel_usba_udc atmel_usba_udc: FIFO at 0x00600000 mapped at c4900000
mice: PS/2 mouse device common for all mice
spi3.0 supply vcc not found, using dummy regulator
setting trigger mode 2 for irq 149 failed (gpio_irq_type+0x0/0x18)
ads7846 spi3.0: trying pin change workaround on irq 149
ads7846 spi3.0: touchscreen, irq 149
input: ADS7843 Touchscreen as /devices/platform/spi_gpio.3/spi3.0/input/input0
rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0
rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!
i2c /dev entries driver
Linux video capture interface: v2.00
AT91: atmel_isi_init_module
AT91: atmel_isi_probe
atmel_isi atmel_isi: Reading configuration
atmel_isi atmel_isi: failed to allocate video buffer
atmel_isi: probe of atmel_isi failed with error -12
at_hdmac at_hdmac: Atmel AHB DMA Controller ( cpy slave ), 8 channels
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock
atmel_mci atmel_mci.0: Atmel MCI controller at 0xfff80000 irq 11, 1 slots
VFS: Cannot open root device "mmcblk0p2" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c002e9dc>] (unwind_backtrace+0x0/0xf0) from [<c031d360>] (panic+0x58/0x180)
[<c031d360>] (panic+0x58/0x180) from [<c0008e5c>] (mount_block_root+0x1d4/0x294)
[<c0008e5c>] (mount_block_root+0x1d4/0x294) from [<c00091d4>] (prepare_namespace+0x158/0x1b0)
[<c00091d4>] (prepare_namespace+0x158/0x1b0) from [<c0008b44>] (kernel_init+0x10c/0x14c)
[<c0008b44>] (kernel_init+0x10c/0x14c) from [<c0029e90>] (kernel_thread_exit+0x0/0x8)

Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext2

Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext2

rootwait [KNL] Wait (indefinitely) for root device to show up.
Useful for devices that are detected asynchronously
(e.g. USB and MMC devices).

rootwait [KNL] Wait (indefinitely) for root device to show up.
Useful for devices that are detected asynchronously
(e.g. USB and MMC devices).