Ник:
Пароль:

Контакты

E-mail: info@starterkit.ru
тел.: +7 922 680-21-73
тел.: +7 922 680-21-74
Телеграм: t.me/starterkit_ru

Способы оплаты

User Info


Добро пожаловать,
Guest

Регистрация или входРегистрация или вход
Потеряли пароль?Потеряли пароль?

Ник:
Пароль:

ПользователейПользователей:2
Поисковых ботовПоисковых ботов:3
ГостейГостей:1

ОбновитьПодробнееВсегоВсего:6
Форум » starterkit.ru » Процессорные модули » SK-iMX6S/D-SODIMM
Не прошиваются некоторые модули imx6s
Elijah1978
Добавлено 11.01.2019 16:52
0
Сообщение: 1
Elijah1978
0

Пункты: 573
Регистрация: 01.08.2017
Досталась в наследство из других проектов несколько модулей imx6s. Прошиваются в MfgTool без сообщений об ошибках. Но по факту там остаётся то же самое что было до прошивки. Не понятно модули залочены на запись или что-то погорело?

Вот что модуль выдаёт в процессе прошивки на терминал:

U-Boot 2013.10 (Dec 02 2013 - 19:49:25)

CPU: Freescale i.MX6SOLO rev1.1 at 792 MHz
Reset cause: POR
Board: Starterkit
DRAM: 512 MiB
Setup enet clock OK
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Using default environment

In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 10800000 ...
Image Name: Linux-3.1.2
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 9382772 Bytes = 8.9 MiB
Load Address: 10008000
Entry Point: 10008000
Verifying Checksum ... OK
Loading Kernel Image ... OK

Starting kernel ...

Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 3.1.2 (user@iMX6-bld) (gcc version 4.7.1 20120402 (prerelease) (crosstool-
NG linaro-1.13.1-2012.04-20120426 - Linaro GCC 2012.04) ) #194 SMP PREEMPT Wed Aug 5 18:
52:19 UTC 2015
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Starterkit i.MX6 sodimm Board
Ignoring tag cmdline (using the default kernel command line)
Memory policy: ECC disabled, Data cache writealloc
CPU identified as i.MX6DL/SOLO, silicon rev 1.1
PERCPU: Embedded 7 pages/cpu @8bc06000 s5664 r8192 d14816 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 89088
Kernel command line: noinitrd console=ttymxc0,115200
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
allocated 2097152 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Memory: 352MB = 352MB total
Memory: 340084k/340084k available, 184204k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xf4600000 - 0xffe00000 ( 184 MB)
vmalloc : 0xa0800000 - 0xf2000000 (1304 MB)
lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.init : 0x80008000 - 0x80526000 (5240 kB)
.text : 0x80526000 - 0x80c94d34 (7612 kB)
.data : 0x80c96000 - 0x80d01730 ( 430 kB)
.bss : 0x80d01754 - 0x80d7113c ( 447 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:624
MXC GPIO hardware
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
Set periph_clk's parent to pll2_pfd_400M!
arm_max_freq=800MHz
MXC_Early serial console at MMIO 0x2020000 (options '115200')
bootconsole [ttymxc0] enabled
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
CPU: Testing write buffer coherency: ok
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
Brought up 1 CPUs
SMP: Total of 1 processors activated (1581.05 BogoMIPS).
devtmpfs: initialized
print_constraints: dummy:
NET: Registered protocol family 16
print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal
print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
hw-breakpoint: maximum watchpoint size is 4 bytes.
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02050000, Cache size: 524288 B
bio: create slab <bio-0> at 0
mxs-dma mxs-dma-apbh: initialized
print_constraints: vmmc: 3300 mV
vgaarb: loaded
SCSI subsystem initialized
spi_imx imx6q-ecspi.3: probed
spi_imx imx6q-ecspi.0: probed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Freescale USB OTG Driver loaded, $Revision: 1.55 $
imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
Advanced Linux Sound Architecture Driver Version 1.0.24.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
Switching to clocksource mxc_timer1
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
_regulator_get: etb supply vcore not found, using dummy regulator
_regulator_get: etm.0 supply vcore not found, using dummy regulator
Static Power Management for Freescale i.MX6
wait mode is enabled for i.MX6
cpaddr = a0820000 suspend_iram_base=a08b4000
PM driver module loaded
iMX6 PCIe PCIe RC mode imx_pcie_pltfm_probe entering.
PCIE: imx_pcie_pltfm_probe start link up.
link up failed, DB_R0:0x0007c500, DB_R1:0x08200000!
IMX PCIe port: link down!
IMX usb wakeup probe
add wake up source irq 75
IMX usb wakeup probe
cpu regulator mode:ldo_enable
i.MXC CPU frequency driver
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
NTFS driver 2.1.30 [Flags: R/W].
fuse init (API version 7.16)
msgmni has been set to 664
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver ldb
_regulator_get: get() with no identifier
imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 128x48
mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver lcd
mxc_sdc_fb mxc_sdc_fb.1: ipu0-di0 already in use
mxc_sdc_fb: probe of mxc_sdc_fb.1 failed with error -16
imx-sdma imx-sdma: loaded firmware 1.1
imx-sdma imx-sdma: initialized
Serial: IMX driver
imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled, bootconsole disabled
console [ttymxc0] enabled, bootconsole disabled
imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
loop: module loaded
GPMI NAND driver registered. (IMX)
vcan: Virtual CAN interface driver
CAN device driver interface
flexcan netdevice driver
flexcan imx6q-flexcan.1: device registered (reg_base=a0958000, irq=143)
flexcan imx6q-flexcan.0: device registered (reg_base=a0960000, irq=142)
FEC Ethernet Driver
fec_enet_mii_bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
add wake up source irq 72
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ARC USBOTG Device Controller driver (1 August 2005)
g_file_storage gadget: controller 'fsl-usb2-udc' not recognized
check_parameters:UTP settings are in place now, overriding defaults
g_file_storage gadget: No serial-number string provided!
g_file_storage gadget: File-backed Storage Gadget, version: 1 September 2010
g_file_storage gadget: Number of LUNs=1
Suspend udc for OTG auto detect
fsl-usb2-udc: bind to driver g_file_storage
mousedev: PS/2 mouse device common for all mice
_regulator_get: spi3.0 supply vcc not found, using dummy regulator
ads7846 spi3.0: touchscreen, irq 362
input: ADS7846 Touchscreen as /devices/platform/imx6q-ecspi.3/spi_master/spi3/spi3.0/inp
ut/input0
_regulator_get: spi0.0 supply vcc not found, using dummy regulator
ads7846 spi0.0: touchscreen, irq 347
input: ADS7846 Touchscreen as /devices/platform/imx6q-ecspi.0/spi_master/spi0/spi0.0/inp
ut/input1
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
_regulator_get: sdhci-esdhc-imx.2 supply vmmc not found, using dummy regulator
mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
mmc1: SDHCI controller on platform [sdhci-esdhc-imx.0] using ADMA
mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
VPU initialized
mxc_asrc registered
Galcore version 4.6.9.6622
Thermal calibration data is 0x5914fc69
Thermal sensor with ratio = 185
Anatop Thermal registered as thermal_zone0
anatop_thermal_probe: default cooling device is cpufreq!
HDMI CEC initialized
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
imx-hdmi-soc-dai imx-hdmi-soc-dai.0: Failed: Load HDMI-video first.
AIC23 Audio Codec 0.1
usb 2-1: new high speed USB device number 2 using fsl-ehci
asoc: tlv320aic23-hifi <-> imx-ssi.1 mapping ok
Initialize HDMI-audio failed. Load HDMI-video first!
ALSA device list:
#0: sgtl5000-audio
NET: Registered protocol family 26
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
mmc0: new high speed DDR MMC card at address 0001
lib80211: common routines for IEEE802.11 drivers
mmcblk0: mmc0:0001 008G30 7.28 GiB
mmcblk0boot0: mmc0:0001 008G30 partition 1 8.00 MiB
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
Bus freq driver module loaded
mmcblk0boot1: mmc0:0001 008G30 partition 2 8.00 MiB
Bus freq driver Enabled
mmcblk0: p1 p2 p3 p4
mxc_dvfs_core_probe
DVFS driver module loaded
mmcblk0boot1: unknown partition table
mmcblk0boot0: unknown partition table
snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)
Freeing init memory: 5240K
hub 2-1:1.0: 4 ports detected
Init: g_file_storage gadget: high speed config #1
/bin/auto_mount: line 5: rdev: not found
EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
/bin/auto_mount: line 5: rdev: not found
mount: mounting /dev/mmcblk0p2 on /mnt/mmcblk0p2 failed: Invalid argument
/bin/auto_mount: line 5: rdev: not found
mount: mounting /dev/mmcblk0p3 on /mnt/mmcblk0p3 failed: Invalid argument
/bin/auto_mount: line 5: rdev: not found
mount: mounting /dev/mmcblk0p4 on /mnt/mmcblk0p4 failed: Invalid argument
OK
Starting logging: OK
Starting watchdog...
Initializing random number generator... done.
Starting network...
eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=1:00, irq=-1)
uuc 0.4 [built Aug 4 2015 11:30:56]
UTP: Waiting for device to appear
UTP: file/device node /dev/utp already exists
cpu_id is 0
UTP: received command 'send'
UTP: sending Success to kernel for command send.
UTP: received command '$ cp $FILE /root/emmc_format'
UTP: executing "cp $FILE /root/emmc_format"
UTP: sending Success to kernel for command $ cp $FILE /root/emmc_format.

Welcome to Buildroot - Initramfs
SK-iMX6-SODIMM_safe login: utp_poll: pass returned.
UTP: received command 'send'
UTP: sending Success to kernel for command send.
UTP: received command '$ cp $FILE /root/u-boot.imx'
UTP: executing "cp $FILE /root/u-boot.imx"
UTP: sending Success to kernel for command $ cp $FILE /root/u-boot.imx.
utp_poll: pass returned.
UTP: received command '$ chmod 777 /root/emmc_format'
UTP: executing "chmod 777 /root/emmc_format"
UTP: sending Success to kernel for command $ chmod 777 /root/emmc_format.
utp_poll: pass returned.
UTP: received command '$ dd if=/dev/zero of=/dev/mmcblk0 bs=1024 count=1024 && sync && s
ync'
UTP: executing "dd if=/dev/zero of=/dev/mmcblk0 bs=1024 count=1024 && sync && sync"
1024+0 records in
1024+0 records out
UTP: sending Success to kernel for command $ dd if=/dev/zero of=/dev/mmcblk0 bs=1024 cou
nt=1024 && sync && sync.
utp_poll: pass returned.
UTP: received command '$ dd if=/dev/zero of=/dev/mmcblk0 ibs=1048576 obs=1048576 seek=15
count=2 && sync && sync'
UTP: executing "dd if=/dev/zero of=/dev/mmcblk0 ibs=1048576 obs=1048576 seek=15 count=2
&& sync && sync"
2+0 records in
2+0 records out
UTP: sending Success to kernel for command $ dd if=/dev/zero of=/dev/mmcblk0 ibs=1048576
obs=1048576 seek=15 count=2 && sync && sync.
utp_poll: pass returned.
UTP: received command '$ /root/emmc_format'
UTP: executing "/root/emmc_format"
Checking that no-one is using this disk right now ...
mmcblk0: p1 p2 p3 p4
OK

Disk /dev/mmcblk0: 238592 cylinders, 4 heads, 16 sectors/track
Old situation:
Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0

Device Boot Start End MiB #blocks Id System
/dev/mmcblk0p1 16 7155 7140 7311360 83 Linux
/dev/mmcblk0p2 7156 7255 100 102400 0 Empty
/dev/mmcblk0p3 7256 7355 100 102400 0 Empty
/dev/mmcblk0p4 7356 7455 100 102400 0 Empty
New situation:
Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0

Device Boot mmcblk0: p1 p2 p3 p4
Start End MiB #blocks Id System
/dev/mmcblk0p1 16 7455 7440 7618560 83 Linux
/dev/mmcblk0p2 0 - 0 0 0 Empty
/dev/mmcblk0p3 0 - 0 0 0 Empty
/dev/mmcblk0p4 0 - 0 0 0 Empty
Warning: no primary partition is marked bootable (active)
This does not matter for LILO, but the DOS MBR will not boot this disk.
Successfully wrote the new partition table

Re-reading the partition table ...

If you created or changed a DOS partition, /dev/foo7, say, then use dd(1)
to zero the first 512 bytes: dd if=/dev/zero of=/dev/foo7 bs=512 count=1
(See fdisk(8).)
mknod: /dev/mmcblk0p1: File exists
mke2fs 1.42.7 (21-Jan-2013)
Discarding device blocks: done
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
Stride=0 blocks, Stripe width=0 blocks
456960 inodes, 1827840 blocks
91392 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=1874853888
56 block groups
32768 blocks per group, 32768 fragments per group
8160 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632

Allocating group tables: done
Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done

EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
UTP: sending Success to kernel for command $ /root/emmc_format.
utp_poll: pass returned.
UTP: received command '$ dd if=/root/u-boot.imx of=/dev/mmcblk0 bs=512 seek=2 && sync &&
sync'
UTP: executing "dd if=/root/u-boot.imx of=/dev/mmcblk0 bs=512 seek=2 && sync && sync"
446+0 records in
446+0 records out
UTP: sending Success to kernel for command $ dd if=/root/u-boot.imx of=/dev/mmcblk0 bs=5
12 seek=2 && sync && sync.
utp_poll: pass returned.
UTP: received command 'pipe tar -zx -C /mnt/mmcblk0p1'
pid is 655, UTP: executing "tar -zx -C /mnt/mmcblk0p1"
UTP: sending Success to kernel for command pipe tar -zx -C /mnt/mmcblk0p1.
UTP: received command 'frf'
UTP: closing the file
UTP: sending Success to kernel for command frf.
utp_poll: pass returned.
UTP: received command '$ sync && sync'
UTP: executing "sync && sync"
UTP: sending Success to kernel for command $ sync && sync.
utp_poll: pass returned.
UTP: received command 'pipe tar -Jx --no-same-owner -C /mnt/mmcblk0p1/opt'
pid is 661, UTP: executing "tar -Jx --no-same-owner -C /mnt/mmcblk0p1/opt"
UTP: sending Success to kernel for command pipe tar -Jx --no-same-owner -C /mnt/mmcblk0p
1/opt.
UTP: received command 'frf'
UTP: closing the file
UTP: sending Success to kernel for command frf.
utp_poll: pass returned.
UTP: received command '$ chmod 0755 /mnt/mmcblk0p1/opt/pmpd'
UTP: executing "chmod 0755 /mnt/mmcblk0p1/opt/pmpd"
UTP: sending Success to kernel for command $ chmod 0755 /mnt/mmcblk0p1/opt/pmpd.
utp_poll: pass returned.
UTP: received command '$ chmod 0755 /mnt/mmcblk0p1/opt/pmpd/pmpd'
UTP: executing "chmod 0755 /mnt/mmcblk0p1/opt/pmpd/pmpd"
UTP: sending Success to kernel for command $ chmod 0755 /mnt/mmcblk0p1/opt/pmpd/pmpd.
utp_poll: pass returned.
UTP: received command '$ sync && sync'
UTP: executing "sync && sync"
UTP: sending Success to kernel for command $ sync && sync.
utp_poll: pass returned.
UTP: received command '$ umount /dev/mmcblk0p1 && sync && sync'
UTP: executing "umount /dev/mmcblk0p1 && sync && sync"
UTP: sending Success to kernel for command $ umount /dev/mmcblk0p1 && sync && sync.
utp_poll: pass returned.
UTP: received command '$ echo Update Complete!'
UTP: executing "echo Update Complete!"
Update Complete!
UTP: sending Success to kernel for command $ echo Update Complete!.
utp_poll: pass returned.
UTP: received command '$ poweroff'
UTP: executing "poweroff"
UTP: sending Success to kernel for command $ poweroff.
The system is going down NOW!imx2-wdt imx2-wdt.0: Unexpected close: Expect reboot!

[ utp_file_read ] copy error
Sent SIGTERM to all processesunregistered gadget driver 'g_file_storage'

Sent SIGKILL to all processes
Requesting system poweroff
imx2-wdt imx2-wdt.0: Device shutdown: Expect reboot!
System halted.
Спуститься к концу Подняться к началу
Персональная информация
sasamy
Добавлено 12.01.2019 21:21 Редактировалось 12.01.2019 21:23 Сообщение: 2
sasamy
4.71

Пункты: 83777
Регистрация: 14.08.2009
Цитата
остаётся то же самое что было до прошивки. Не понятно модули залочены на запись или что-то погорело?


Попробуйте создать файл или скопировать из одного места в другое существующий и перезагрузиться. Если файл после перезагрузки сохранится - понятно будет что дело не в emmc, если конечно файловая система не в ram и не в режиме только чтение.
Спуститься к концу Подняться к началу
Персональная информация
Elijah1978
Добавлено 15.01.2019 18:27 Сообщение: 3
Elijah1978
0

Пункты: 573
Регистрация: 01.08.2017
удалось войти в командную строку при прошивке как
SK-iMX6-SODIMM_safe login: root

сделал на всякий
#mount /dev/mmcblk0p1 -o remount,rw
скопировал файл в /
При перезагрузке файл не сохранился.

/dev/mmcblk0p1 это наверное emmc, а не ram.

т.е. emmc погорело?
Спуститься к концу Подняться к началу
Персональная информация
Pavel Ivanchenko
Добавлено 15.01.2019 18:37 Сообщение: 4
Pavel Ivanchenko
Admin
4.39

Пункты: 93008
Регистрация: 24.03.2009
Пол: Мужчина
Странно, почему вопрос к нам а не к предыдущему владельцу ...
Еслиб emmc "погорела" - тогда и не грузилось бы.
Возможно включен режим аппаратной защиты от записи в emmc - как отключить (и можно ли вообще), не знаю.
Спуститься к концу Подняться к началу
Персональная информация
Elijah1978
Добавлено 15.01.2019 19:04 Сообщение: 5
Elijah1978
0

Пункты: 573
Регистрация: 01.08.2017
А какими средствами осуществляется аппаратная защита?
Если нам вдруг понадобиться?
Спуститься к концу Подняться к началу
Персональная информация
sasamy
Добавлено 15.01.2019 19:39 Редактировалось 21.01.2019 13:02 Сообщение: 6
sasamy
4.71

Пункты: 83777
Регистрация: 14.08.2009
Цитата
А какими средствами осуществляется аппаратная защита?
Если нам вдруг понадобиться?


В buildroot есть mmc-utils

https://manpages.debian.org/unstable/mmc-utils/mmc.1.en.html

PS в мане неполная информация - лучше смотреть help

https://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git/tree/mmc.c#n72
Спуститься к концу Подняться к началу
Персональная информация
Elijah1978
Добавлено 13.02.2019 16:28 Сообщение: 7
Elijah1978
0

Пункты: 573
Регистрация: 01.08.2017
Оказывается нужно было прописывать в ucl2.xml arm-sdtool :
...
<CMD state="Updater" type="push" body="send" file="arm-sdtool">Sending sdtool</CMD>
<CMD state="Updater" type="push" body="$ cp $FILE /root/arm-sdtool"/>
<CMD state="Updater" type="push" body="$ chmod 777 /root/arm-sdtool"/>
<CMD state="Updater" type="push" body="$ chmod 777 /root/emmc_format">eMMC prepare ...</CMD>
<CMD state="Updater" type="push" body="$ /root/arm-sdtool /dev/mmcblk0 unlock || test $? -eq 253">eMMC unlock ...</CMD>
<CMD state="Updater" type="push" body="$ dd if=/dev/zero of=/dev/mmcblk0 bs=1024 count=1024 && sync && sync">Clean partitions of eMMC</CMD>
...

рабочий бинарник arm-sdtool, где-то достал, всё прошивается. Но что это за пакет такой особо не гуглится...
Спуститься к концу Подняться к началу
Персональная информация
sasamy
Добавлено 14.02.2019 13:28 Сообщение: 8
sasamy
4.71

Пункты: 83777
Регистрация: 14.08.2009
Цитата

рабочий бинарник arm-sdtool, где-то достал, всё прошивается. Но что это за пакет такой особо не гуглится...


https://github.com/BertoldVdb/sdtool

mmc-utils поддерживает намного больше возможностей eMMC
Спуститься к концу Подняться к началу
Персональная информация
Форум » starterkit.ru » Процессорные модули » SK-iMX6S/D-SODIMM